Matt machine It is a mat switch to protect the worker, the elderly, the weak.
The mat switch is the basis for detecting people and ensuring safety. Fail-safe 4-wire type is compatible with domestic and domestic chemical specifications. Various mat switches can be installed in various places.

Mat switch and handling precautions will be explained.
Please read it for safe use.

A) General precautions.
Do not pull the lead wire or use it with care when installing and transporting. It may cause a disconnection accident.
Please do not use nails or screws as it will cause a short circuit when installing the mat switch.
When fixing, we recommend using adhesive, double-sided tape, channel and joint construction.

• Use within the temperature range specified in the specifications.
• Use in flooded condition is dangerous. (Waterproof, spinning depends on the product).
• Do not use the product in places where it is attached to solvent such as thinner, benzene, toluene, etc., although the life of the product
    is weak in general products such as weak acid and alkali solution.
• Since it may cause irregular surface irregularities, we ask for installation in a flat place.
• The switch is always off. Do not turn on the unit for a long period of time by moderate or heavy.

• Use the specified voltage and current value for safety reasons and the life of the switch.
     Maximum AC 100V, DC 30V, 1A capacity, please use AC, DC 30V, 1A or less.

The warranty period of the delivered product will be one year after delivery.
During the warranty period, if the fault occurs due to the responsibility of the company, the defective product will be replaced or repaired free of charge. However, please note that the following cases will be excluded from the warranty.

And accessories for fixing the mat switch. When laying a mat switch, refer to the calculation method of safety distance according to EN999 (ISO13855).

It is an accessory for prevention of accident of a mat switch

You can add slope (slope) directly to the rubber material without any joints (optional).

The formula given in EN999 for floor mats
S = (1600 × T) + 1200mm
S is the minimum safety distance (unit: mm) coefficient 1600 is set to 1600mm / s standard approach speed,
T is the total stopping time (unit: second), considering 1200mm stride and arm length
The total downtime consists of two parts.
T = t1 + t2
t1: Maximum time until the output power of the control unit is turned off in the detection installation track (35 ms in case of this safety mat)

t2: Response time of the machine. That is, the time required for the machine to stop or remove the hazard after receiving the output of the safety mat system
The response time of the machine used for the calculation should be the worst-case time. Depending on the machine, The response time may vary depending on mode, type of workpiece and stopping point during the cycle.


If you can influence the response time, such as brake wear, you should anticipate these factors as well.


Here is an example of a safety mat with a machine whose worst response time is estimated to be 0.485 seconds.
By the above expression

T = t1 + t2
= 35ms + 485ms
= 520ms = 0.520s
S = (1600 x 0.520) + 1200 mm = 832 + 1200mm = 2032mm Therefore, the safety mats should be laid at a distance of 2032mm from the hazardous circle.

We are custom-made mat switch of irregular shape such as circle or ellipse.

It is easy to install without being noticeable by a roaming detection mat such as a hospital and a nursing facility.

It lies in the factory or in the vicinity of AGV robots factory or access restricted area.

Special space, can be cut diagonally depending on the installation location such as factories and hospitals.
For custom mat switch use, we recommend the use of fail-safe 4-wire and CE certified PSSU controllers.
For more information on fail-safe, PSSU controllers, see the page of the controller.

The existing CVP-2335 mat switch has been renewed to increase softness, durability and texture.
Improved surface cushioning, flexibility and durability is also UP because it uses a flat line to move the inner switch.
The cable adopts a robot cable and has excellent flexing resistance, twisting resistance and sliding resistance.
In addition, it improves the retractability, and it is easy to accommodate three broken.
It is easy to store because it can fold three fold.


It is difficult to slip on the bottom of the floor as well as the existing type
There are three types of non-slip type, CVP2335, anti-skid, nursing matt switch, anti-slip cover.
Security safety applications, as well as current anti-rope · replacement of nursing mat switch

You can easily install without noticeable rope detection mat

Depending on the existing beige lot type of conventional, it is also possible to respond to different colors.

Until now, as a non-slip countermeasures, we also prepared a mat switch with anti-slip.
Slip-proof function (the type of non-slip sheet fused to the bottom)

The existing CVP2335 is also easily removable non-slip cover

It is made of double-sided muscle rubber, so there is no front or back left side of the code is available in both right
Because it is a 4-wire type, it can detect disconnection by using controller. It can also be used as safety switch. Because it uses NBR rubber, it has excellent oil resistance and heat resistance.

Step step mat switch · Various safety mat switchIt can be widely used as guest alarm, intruder detection, roaming detection mat switch.

Small size 280mm × 500mm × 12mm Thickness Lead wire length 1.5mLarge size 280mm × 1000mm × 12mm Thickness Lead wire length 1.5m